1 thought on “Introduction to LED light band price and installation guide”

  1. As the development of the lighting industry has improved, many emerging lighting has now appeared. Among them, the LED light belt is the most popular lighting now. The LED light zone is assembled on FPC or PCB hard board. It looks like a strap one by one. Generally, the LED light belt is 80,000 to 100,000 hours. The LED light belt is not only environmentally friendly but also energy -saving when it is used. So the LED lights are widely welcomed. However, many friends are not very familiar with the LED light belt, so then I will give you a detailed sharing knowledge about LED lights in detail. I hope it will be helpful to everyone.

    LED light belt price
    LED light bands are currently very popular. It is not only rich in color, but also energy -saving and environmentally friendly. use. At present, the price of the LED light belt is not very expensive. If it is a single color, one meter is between a few yuan and a dozen yuan. If it is a color RGB, it is more expensive, and the price of different specifications and different varieties is different. Specifically, the price is about 5 yuan to tens of yuan. It is recommended that there is no 220V high -pressure lamp belt, and the high -pressure lamp belt is high when the light is high. Life will be relatively short. Low -pressure lamp bands have a long life, energy saving and environmental protection, and higher safety factor than high -pressure lamp bands. The living room is best to use a 12V LED soft light bar, a waterproof bare lamp bar or a waterproof ticking light bar. The specific brightness is selected according to the optical effect. If you are high, you can choose 5050, 60 lights, one meter or 5050, 30 lights and one meter. You can choose 3528, 60 meters per light with low brightness. For optical effects, you can choose monochrome, or you can choose colorful or horse -raid light strips.
    The general price range according to the material without lamp band
    3528: 5-15 yuan/meter; 5050: 16-29 yuan/meter;

    n n installation installation Guidelines
    1. Interior installation: LED light bands are used for indoor decoration, because it does not need to withstand wind and rain, the installation is very simple. Taking the LED light band produced by Guanghong Electronics as an example, each LED lamp belt is packed with self -viscosity 3M double -sided glue. You can directly remove the sticker on the surface of 3M double -sided glue surface during installation, and then fix the light bar to fix it in need. The place of installation is just flat. What should I do if some places need to be turned or grow? It is very simple. The LED light belt is a circuit structure composed of 3 LEDs as a set of collateral methods. Each LED can be cut and used separately.
    2. Outdoor installation: Outdoor installation will withstand the wind and rain. If it is fixed with 3M glue, it will cause 3M adhesive to reduce the LED lights. Fixed way. The place where it needs to be cut and connected. The method is the same as the indoor installation, but it is necessary to be equipped with waterproof glue to consolidate the waterproof effect of the connection point.
    3. The power supply connection method: The general voltage of the LED light belt is DC 12V, so the power supply is required to supply power. The size of the power supply is determined according to the power and connection length of the LED light band.如果不希望每条LED灯带都用一个电源来控制,可以购买一个功率比较大的开关电源做总电源,然后把所有的LED灯带输入电源全部并联起来(线材尺寸不够的话可以另外延长), Unified power supply by the total switching power supply. The advantage of this is that it can be concentrated. If it is inconvenient, it is not possible to achieve the lighting effect and switch control of a single LED light belt. Which method can be measured by itself.

    4. Controller connection method: LED horse -raid lamp belt and RGB full color lamp belt need to use the controller to achieve the change effect, and the control distance of each controller is different. Generally, For speaking, the control distance of the simple controller is 10 to 15 meters, the control distance of the remote controller is 15 to 20 meters, and the maximum can be controlled to 30 meters distance. If the connection distance of the LED light band is long and the controller cannot control such a long lamp band, then the power amplifier is needed to be used for distribution.
    5. Pay attention to the connection distance of the LED light belt: Generally speaking, the 3528 series LED light belt, its connection distance is up to 20 meters, the 5050 series LED light belt, the longest connection distance is 15 meters. If this connection distance is exceeded, the LED light belt is easy to heat, and it will affect the service life of the LED light zone during use. Therefore, when installing, be sure to install it according to the requirements of the manufacturer, and avoid letting LED lights run over the load.
    How to identify quality
    The markets of LED lights are different, and the price of regular manufacturers and cottage manufacturers is very different. If the quality of the LED light belt is identified from the professional technology, I am afraid that many customers do not have this ability. But we can make preliminary identification from a simple appearance, and we can basically distribute the quality.
    M:
    1. Look at the solder joints. The LED lamp band produced by the regular LED lamp belt producer is produced with SMT patch process, which is produced with tin paste and backwing welding. Therefore, the solder joints on the LED lamp belt are relatively smooth and the amount of weld will not be large. The solder joints extend from the FPC pad to the LED electrode.
    2. Look at the quality of FPC. FPC is divided into two types: copper and pressing copper. The copper foil of the copper plate is protruding. If you look closely, you can see it from the connection between the pad and FPC. The compressive copper is closely integrated with the FPC, and it can bend arbitrarily without a pads fall off. If the copper plate is curved too much, the pad will fall off. The temperature is too high during maintenance.

    3. See the cleanliness of the surface of the LED light. The LED light band produced by SMT process has a very good surface cleanliness, and no impurities and stains are visible. The cottage LED lamp belt produced by hand welding process, no matter how cleaning its surface, it will remain with stains and scrubbing marks.
    4. Look at the packaging. The regular LED lamp band will be packaged with anti -static roll discs, 5 meters or 10 meters of volumes. The anti -static moisture -proof packaging bag is used outside the packaging. The cottage version of the LED lamp band uses a recycling roll plate. There is no anti -static moisture -proof packing bag. If you look closely, you can see the traces and scratches left by the label when the appearance is cleared.
    5. Look at the label. There will be a print label on the regular LED lamp belt packaging bag and roll plate, not a printing label.
    6. Look at the attachment. The regular LED light zone will be attached to the packaging box to use instructions and lamp specifications, and it will also be equipped with a LED light belt connector or card seat; while the copycat version of the LED light belt box does not have these accessories because After all, some manufacturers can still save.
    The above is the knowledge about the LED light band in detail about the LED lights. I hope that you can better understand the LED light belt knowledge through our sharing. LED lights are increasingly popular in our lives. Especially the style of the LED light belt is very romantic. There are also many characteristics of the LED light belt. For example, it is very soft, can be arbitrarily curled, and can be cut and delayed, and it is not easy to deform. The life is also very long. In addition, its most popular feature is very energy -saving. The above we have shared the knowledge of the LED light belt very detailed, I hope it will be helpful to everyone.

Leave a Comment

Shopping Cart